1. Home
  2. Blog
  3. Battery Module Cost per Cycle: Lifetime Throughput Compared

Battery Module Cost per Cycle: Lifetime Throughput Compared

Short answer: Purchasing price per kWh is an incomplete metric for battery modules. Lifetime energy throughput (rated capacity multiplied by cycle count multiplied by depth of discharge) gives a far more useful basis for comparison. Divided by acquisition cost, it produces a cost-per-kWh-delivered figure that reflects what you actually pay for over the module's service life.

Procurement teams comparing battery modules almost always start with price per kWh of rated capacity. It is a convenient shorthand, but it omits the single most important variable: how many times you can use that capacity before the module reaches end of life. Two modules at the same price per kWh can differ by a factor of two or more in what they actually deliver over their lifetimes. This article sets out a straightforward method for comparing modules on lifetime energy throughput, works through three catalogue examples, and flags the caveats that matter before you apply the numbers.

Why price per kWh is an incomplete metric

A battery module's rated capacity (in kWh) describes what it holds at the beginning of life under standard test conditions. It says nothing about:

  • How many full cycles the module is rated for before capacity falls to the end-of-life threshold (typically 80 % of initial capacity).
  • At what depth of discharge (DoD) that cycle count was measured.
  • What the usable capacity is at the DoD your application actually imposes.

Without those three inputs, a lower headline price per kWh may simply mean fewer lifetime cycles, so the delivered cost per kWh is higher, not lower. The IEC standard IEC 62619, which covers safety requirements for secondary lithium cells and batteries used in stationary applications, requires cycle life to be characterised under defined test conditions precisely because the number is application-dependent.

The lifetime throughput formula

Lifetime energy throughput is defined as:

Throughput (kWh) = Rated capacity (kWh) x Rated cycle count x DoD

All three variables must come from the same datasheet row. Cycle counts stated at 80 % DoD are not interchangeable with counts stated at 100 % DoD or 60 % DoD: a deeper discharge generally reduces the rated cycle count, and a shallower discharge generally extends it. The datasheet is the only authoritative source.

Once you have the throughput figure, the levelised cost of storage at the module level is:

Cost per kWh delivered = Acquisition cost (your currency) / Throughput (kWh)

This formula intentionally leaves the acquisition cost blank. Avantis Energy does not publish list prices; your cost input comes from the quotation for your specific volume and configuration. The formula works regardless of currency or unit.

Three catalogue modules worked through

The following calculations use only the figures published in the Avantis Energy catalogue. All three modules are NMC chemistry. Cycle life is stated at 80 % DoD on each datasheet; that is the DoD used in every calculation below.

Module Configuration Rated capacity Cycle life at 80 % DoD Lifetime throughput
VDA 355 (1P4S) NMC 2.59 kWh 2,000 cycles 2.59 x 2,000 x 0.80 = 4,144 kWh
VDA 355 (2P6S) NMC 2.55 kWh 1,500 cycles 2.55 x 1,500 x 0.80 = 3,060 kWh
MEB 590 (2P8S) NMC 6.66 kWh 1,200 cycles 6.66 x 1,200 x 0.80 = 6,394 kWh

The MEB 590 module delivers the highest absolute throughput because its capacity is substantially larger, even though its rated cycle count is the lowest of the three. The 1P4S VDA 355 delivers more throughput than the 2P6S despite comparable capacity, because its cycle rating is one-third higher. Neither observation would be visible from capacity alone.

To apply the cost formula: divide your quoted acquisition cost per module by the throughput figure in the right-hand column. The result is your cost per kWh delivered over the module's rated life. That figure is comparable across modules, chemistries and form factors, as long as the DoD basis is consistent.

For more detail on the MEB format, see the next-generation MEB platform battery module.

What the throughput figure does not tell you

Lifetime throughput at the module level is a useful procurement filter, not a system design guarantee. Several factors sit outside it:

System-level life is not the same as module-level life. Inverters, thermal management systems and balance-of-plant components each carry their own service intervals and replacement costs. A complete cost-of-ownership model must include those. The business case for commercial and industrial energy storage covers the system-level picture in more detail.

Warranty terms define what the manufacturer will stand behind, not what the chemistry can theoretically deliver. Throughput on a datasheet is a rated figure under specified test conditions. Warranty coverage (in cycles, years or kWh delivered) is a contractual commitment and may differ from the datasheet maximum. See battery warranty: cycles, throughput, years and end capacity for a full treatment of warranty metrics.

DoD consistency is essential. A module rated at 2,000 cycles at 80 % DoD cannot be directly compared with one rated at 2,000 cycles at 60 % DoD. The throughput at 60 % DoD is 25 % lower per cycle. If your application runs at a DoD other than the datasheet basis, ask for cycle life data at your actual operating DoD before applying the formula.

Temperature and charge rate affect realised cycle life. Datasheets are measured under standard laboratory conditions. Operation at elevated temperatures or at high C-rates typically reduces realised cycle life below the rated figure. The IEA's battery technology tracking consistently identifies thermal management as one of the primary determinants of field service life.

When automotive NMC modules are not the right choice for stationary duty

The three modules worked through above are NMC automotive formats: VDA 355 and MEB 590. Their cycle ratings (1,200 to 2,000 cycles at 80 % DoD) are appropriate for vehicle duty cycles, where the number of full cycles per year is relatively low.

For stationary applications running daily full cycles, 1,200 to 2,000 cycles corresponds to roughly three to five years of service life under heavy use. Purpose-built ESS modules are characterised at 8,000 cycles and above at 80 % DoD, which changes the throughput calculation substantially. Applying the same formula to an ESS module rated at, for example, 100 Ah and 8,000 cycles produces a lifetime throughput that makes the automotive modules look expensive per kWh delivered, even if the ESS module costs more per kWh of rated capacity.

For procurement teams specifying daily-cycling stationary storage, the battery modules from Avantis Energy page lists both automotive and stationary formats with their respective cycle ratings, which is the starting point for a valid comparison. The energy storage solutions section covers system-level guidance.

Applying the method in practice

A procurement comparison using lifetime throughput requires three inputs per module: rated capacity from the datasheet, rated cycle count at a stated DoD, and your acquisition cost from the quotation. With those three numbers, the formula above produces a directly comparable cost-per-kWh-delivered for each line item. Differences in form factor, configuration or chemistry are already captured in the capacity and cycle figures; no additional adjustment is needed as long as the DoD basis is the same across all candidates.

If datasheets state cycle life at different DoD values, normalise to a common DoD before comparing, or ask the supplier for cycle data at your target DoD. Do not mix 80 % DoD and 100 % DoD figures in the same table.

Frequently asked questions

What is lifetime energy throughput for a battery module?
Lifetime energy throughput is rated capacity (kWh) multiplied by rated cycle count multiplied by depth of discharge. It represents the total energy a module is specified to deliver before reaching end-of-life capacity. It is the correct basis for comparing modules of different sizes and cycle ratings on a cost-per-kWh-delivered basis.

Why does depth of discharge matter when comparing battery module cycle life?
Cycle life figures on datasheets are always tied to a specific DoD. A module rated at 2,000 cycles at 80 % DoD and one rated at 2,000 cycles at 60 % DoD deliver very different lifetime throughputs: 20 % less energy per cycle in the second case. Comparing cycle counts without checking the DoD basis produces misleading results. Always use the same DoD when calculating throughput across candidates.

Are VDA 355 and MEB 590 modules suitable for daily-cycling stationary storage?
They can be used in stationary applications, but their cycle ratings (typically 1,200 to 2,000 at 80 % DoD) are designed for vehicle duty cycles. Applications requiring daily full cycling over ten or more years are better served by purpose-built ESS modules, which are characterised at 8,000 cycles and above at 80 % DoD. The difference in lifetime throughput per unit of acquisition cost is substantial.

How do I calculate cost per kWh delivered for a battery module?
Divide your acquisition cost per module by the lifetime energy throughput in kWh. Throughput equals rated capacity multiplied by rated cycle count multiplied by DoD, with all three values taken from the same datasheet row at the same DoD. The result is your levelised module cost in cost units per kWh delivered, comparable across different module formats.

Where can I find cycle life and capacity data for Avantis Energy modules?
Rated capacity and cycle life at stated DoD are published on each product page in the cell and module catalogue. The datasheet is the authoritative source for all specification inputs.

Next step

Review rated capacity and cycle life figures for the full NMC module range, then apply the throughput formula to your quoted acquisition cost. View the module range or ask a technical question if you need cycle data at a DoD other than the datasheet basis.